Tag Archives: shore

Due to unforeseen car repair cost I have to put one of my Star Wars Costume up for sale. For Sale is my Shore trooper costume which is partially built. It has been worn a few times for a total time of probably 3 hours each at conventions. The whole armour is painted with the right colour of Sahara beige. Sale includes the following loose parts. 2 X plastic shoulder straps. 1 x Chest Armour. 1 x Upper back Armour. 2 x Piece of plastic to attach chest armour to upper back armour. 2 x Shoulder Bell. 2 x Bicep Armour. 2 x Forearm Armour. 1 x Stomach armour. 1 x Lower back armour. 1 x Belt with resin buckle with various ammo boxes attached as well as the waist cape. 1 X Detonator can with 2 x ammo boxes attached. 2 X leg armour with 2 pieces to keep the leg armour together. 1 X homemade neck seal. 1 x homemade tunic to wear under the armour. 1 x brown trousers. The helmet is made out of plastic expect the snout, chin exhaust and the forehead plate which are made out of resin. The helmet could do with a bit of tidying up. A hard hat liner has been attached to the inside of the helmet. I have installed a basic strapping system to attach the shoulder bells, bicep to the upper chest armour. The plastic straps at top are attached by Velcro. The collar is attached the back armour by zip ties, the resin exhaust at the back would need a repaint or a rebuild. The chest and back armour is attached together by a piece of shaped plastic with Velcro (needed to be painted). The armour wraps around the wearer stomach. The side panels has been glued on but could be removed to fit a larger waist or panels could be trimmed to fit a smaller waist. The armour has been adjusted to fit my waist of 34 inches. Right and left arm armour. A basic strapping system is attached to the shoulder bell and bicep. The forearm armour has foam inserted so it will fit snugly the forearm. The back hand armour has Velcro installed which is attached to a pair of leather gloves which fits a size small/medium size hands. Belt and waist cape. The waist cap is made out of heavy cotton which is attached to the belt. The ammo boxes are attached to the belt with Velcro. The buckle is 3D printed out of resin/plastic I think. The detonator can & ammo boxes attaches to the back of the belt with Velcro. Leg armours has been constructed together with zip ties and Velcro. There is a gap at both leg armour so that you can put your leg in, the gap is covered by a piece of armour which attached by a piece of armour which is attached by Velcro. The buckles at the side of the armour are made of resin. Basic brown trousers which can fit 34inch waist. Homemade tunic (fit medium to large) which is worn under the armour. There is plenty of life left in this armour. Im sorry to see this costume go but hopefully this set of armour will go to a new home where it is worn out frequently! Thank you for looking. The item “Shore Trooper Helmet Star Wars Cosplay Costume Armor Armour Prop Storm Trooper” is in sale since Sunday, April 08, 2018. This item is in the category “Collectables\Science Fiction Collectables\Star Wars Collectables\Star Wars (1977)”. The seller is “hamsterboy501″ and is located in Stockton-on-Tees. This item can be shipped to United Kingdom, Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Australia, United States, Russian federation, Canada, Brazil, Japan, New Zealand, China, Israel, Hong Kong, Norway, Indonesia, Malaysia, Mexico, Singapore, South Korea, Switzerland, Taiwan, Thailand, Chile.

• Series/ Genre: Star Wars